Pneumatics

What's 'Pnew' in Pneumatics?

With Alternative Solutions Available, Machine Builders and End Users Still Find Plenty of Appeal in Pneumatic Systems

By Mike Bacidore

Despite an evolution of alternatives, pneumatics have stood the test of time. Hydraulic and electromechanical systems might offer a better solution in certain circumstances, but there are still plenty of pneumatic applications. We gathered input from a panel of industry veterans to determine how prevalent the technology still is and what to consider when making a decision.

Participants include TJ McDermott, project manager at Systems Interface, a systems integrator in Bothell, Washington; Chico Marks, manager of total plant maintenance, Subaru of Indiana Automotive in Lafayette, Indiana; Randy Nobles, regional vice president at Womack Machine Supply; Scott M. Maurer, product manager—air line at SMC; Frank Langro, director, marketing, product management, at Festo; Jerry Scherzinger, marketing pneumatics product manager at Bimba; Nathan Irvine, application and technical support, and Marchelle Forish, senior product specialist at Aventics, and Bill Savela, marketing director at Delta Computer Systems.

What do pneumatics have to offer that still make them a viable solution?

Nobles: Pneumatic systems are still easy to implement and maintain. Also, the operational speed for the amount of money invested is very attractive.

CD1411PneumaticsBillSavela

Bill Savela

Savela: Pneumatics can provide an optimal combination of force and compliance when controlled by a closed-loop motion controller with special capabilities for controlling both pressure/force and actuator position.

Scherzinger: Pneumatic devices are relatively low-cost and typically highly configurable, making them a great choice for both OEMs and MROs looking to provide a solution. Standard pneumatic actuators can, for example, be ordered in a wide variety of bore sizes, stroke lengths and mounting styles, making them highly flexible and capable of providing forces ranging from a few ounces—small bore sizes with low pressure—to over 10 tons—large bore sizes at 250 psi air pressure—in stroke lengths from fractions of an inch to 10 ft. Additionally, because pneumatics use air as the media, it is a clean source of work when compared to hydraulics, which uses hydraulic oil. A leak in a pneumatic system simply vents air to the atmosphere, but a leak in a hydraulic circuit discharges oil, requiring extensive cleanup and proper disposal.

Langro: Pneumatics can offer a variety of features that still makes it attractive to use. Pneumatics has few electrical connections and can be

CD1411Pneumatics7006ac

Source: Festo

suitable in washdown areas. Also, the power density of pneumatics offers an advantage over electrics in applications such as stamping and pressing. When compared to a hydraulic solution, pneumatics can be a cleaner installation, which is clearly important to industries including pharmaceutical, food and beverage and semiconductor.

Also Read: Is Pneumatics Still a Good Solution?

What is your primary reason for choosing pneumatics?

McDermott: In the short term, a pneumatic solution usually costs less than an electric linear motor approach. The capital cost of linear motors typically far exceeds simple pneumatics. However, the longer a pneumatic system is in service, the higher the cost. Maintenance costs climb, and air leaks add to the cost. On the other hand, pneumatic systems are generally easier to troubleshoot. This is especially important when the knowledge pool in a maintenance department is decreasing due to attrition. A linear motor, likely involving a VFD and motion logic, needs maintenance staff skilled in motion control programming. We pick the solutions that fit the application. A pneumatic ram is a good choice for an on-deck hawser winch brake. It's relatively compact for the force exerted, and is easy to maintain and quite robust. For the remote actuator bank, running it via a common Fieldbus protocol such as Ethernet/IP or Profinet is the only way to go. Pulling many conductors for traditional central control is more costly than pulling a single Ethernet cable. The Fieldbus hardware is very reliable and using a device level ring gives redundancy for even more robustness.

Nobles: The primary reasons for using pneumatics are simplicity, compressed air availability and experience. We are seeing interest in conversion to electric actuators, but this trend hasn't been vast.

Savela: Pneumatics excels in applications that require the application of precise amounts of pressure or force, yet those that also benefit from the compliance of the air medium. Using electric motors in such applications would cost more and be more difficult to implement. In addition, holding a load in a pneumatic system can consume less energy, possibly zero, in a closed system, which isn't possible with an electric motor, unless an expensive braking scheme is implemented.

CD1411PneumaticsFrankLangro

Frank Langro

Langro: The choice to use pneumatics, hydraulics, or electrics really should come down to the application requirements. What are you trying to move? How fast do you need to do it? What type of accuracy and repeatability is required? Are you planning to run multiple products that will require constant changeover? What are the environmental considerations? Based on these factors, you start to see which options offer the most viable solution. Pneumatics is a great choice for a case erector where the motion is highly repetitive and the motion requirements are not high precision. In contrast, a wafer inspection process in the semiconductor industry involves variable positions and requires high accuracies and repeatability, making an electrical-type motion solution more suitable for this application.

 Can you talk about the types of machines or applications you're using pneumatics for?

Marks: We use pneumatics for the majority of our applications in the plant. They includes automated material handling, parts positioning for welding, paint application and bolt and fastener tightening. We do this with end-of-arm tooling on robots, dedicated clamping and positioning equipment, paint application bells and guns, and handheld fastener tightening torque guns.

We use pneumatics for the majority of our applications in the plant. This includes automated material handling, parts positioning for welding, paint application and bolt and fastener tightening.

Nobles: Womack is using pneumatics in several industries. We have applications on packaging, well service, food processing, and utility service equipment, to name a few.

Langro: Pneumatics are used in just about every industry that's involved in high- and even low-volume manufacturing. For example, diverse industries such as the automotive, semiconductor, pharmaceutical and food and beverage all have use for pneumatics in their various applications. Pneumatics can be found in the clamping and stamping of sheet metal parts in an automotive press shop, the lifting and transferring of wafers, and the coating of tablets in the pharmaceutical industry. Pneumatics is also found in gas box panels in the semiconductor industry. A common use of pneumatics is in the packaging of products. Pneumatics can be found in just about every machine that forms, fills or seals.

CD1411PneumaticsJerry2

Jerry Scherzinger

Scherzinger: As a manufacturer, our components—actuators, valves, fittings, manifolds, FRLs—are used on a tremendously wide variety of machines designed for many applications. The applications range from agricultural equipment and transportation vehicles, which need to withstand harsh outdoor environments, to food processing and packaging equipment exposed to corrosive washdown chemicals and medical devices that require a high degree of precision. Common in-plant manufacturing applications include material handling equipment such as conveyor diverters and pick-and-place equipment.

Savela: Fluid power applications in general benefit from the medium's ability to be used when pressure or force must be controlled in an application, and, within these application types, pneumatics excels when the application can benefit from a degree of compliance. Because air is much more compressible than hydraulic fluid, pneumatics can have an advantage in applications where force control is required, but which also need to have some give when an actuator and a work piece come together. Pneumatics are also especially useful in applications where the load can be subject to unknown shocks, bending applications where a force must be applied to the load to do the work, and force-backing applications where the load must have an accurate known force applied to it, such as a metal riveting application. Consider a press roll that is used to hold down lengths of logs as they are fed into a piece of sawmill equipment such as a planer, edger or bandmill. Controlling the press rolls means holding logs tightly without damaging them so as to not destroy valuable timber. Logs can be moving as fast as 2000 board ft/min, and the press rolls may need to sustain a force of up to 1,800 lb in order to maximize productivity. Adaptation of press roll positioning to maintain desired force without damaging the logs, even as log surface profiles are rapidly changing, can be accomplished better using pneumatics than other technologies.

CD1411PneumaticsDeltaSystemsSmall

How does a pneumatic solution compare to an integrated linear motor package, when considering cost, footprint and plug-and-play?

CD1411PneumaticsMarksChico7

Chico Marks

Marks: Pneumatics are cheaper and simpler than linear motor packages from both an engineering and maintenance perspective. From an engineering view, PLC-controlled pneumatics are typically easier to design than a motor, requiring less PLC code, simpler position sensing, less complicated motion control, and less costly components. Maintenance enjoys many of the same benefits. Spare parts are both less expensive and simpler to install; they are typically plug-and-play, requiring minimal training and no parameter setup. However, these advantages come with a tradeoff. These simpler pneumatic systems are not as precise in their positioning or motion control as an electromechanical system. While it is true that a pneumatic system can be designed to be very precise, this would eliminate many of the benefits of using pneumatics.

Savela: Pneumatics can handle high-cycle force applications that would degrade electromechanical solutions in a short period of time. An electromechanical solution may be more appropriate for applications which require speeds greater than about 40in./sec or accuracies better than 0.005 in., but most electromechanical solutions will not be able to match the life of a pneumatic solution in a force control application. In general, although they're typically fine for applications that do position control, linear electric motors aren't good for controlling force. Coupled with a proportional valve and precise transducers, a closed-loop motion controller can attain the same level of positioning accuracy as a linear motor, while also controlling pressure/force to a high degree of accuracy. Assuming that the pump, valve and control system can be mounted away from the actuator, but not too far away, a pneumatic solution can have a very small footprint at the actuator site and can place less weight on the moving actuator than a motor would. In applications that must apply and hold a given amount of force on an object, pneumatic systems have the advantage of being able to do so with lower energy consumption than electric motors, even linear ones. From the perspective of ease of use, a pneumatic system incorporating a motion controller with special support for fluid power control can be very easy to set up. For example, Delta Computer Systems' motion controllers are supported by RMCTools, a programming package that employs graphical tools to simplify system development and tuning. An example of one of Delta’s tools is the Plot Manager, which allows the designer to view the actual motion profile versus the target profile, so that errors can be removed via fine tuning.  The screen capture below shows a plot made with the Plot Manager.

CD1411PneumaticsDeltaSystemsGraphSmall

Nobles: Pneumatic solutions tend to be more cost-effective and have a smaller footprint than a competitive linear motor package. The plug-and-play aspect of these systems is comparable.

Langro: Pneumatics is typically a lower-cost option than a linear motor package and can be operated with a simple electrical signal from a PLC output. An integrated linear motor could be five times the product cost and requires more advanced programming to get the same positioning function. What a linear motor package can offer over pneumatics is flexibility, enabling the machine to be easily reconfigured to handle different products.

CD1411PneumaticsHeadshotIrvine2014Irvine: Pneumatic solutions remain favorable versus electric drives for applications requiring low to moderate force and speed on low to moderate duty cycles. Low initial capital costs and generally long cycle life frequently lead to lower total cost of ownership in such applications.





{pb}

What factors need to be considered when searching for a remote actuator valve bank to communicate digitally to a PLC and control pneumatic devices?

Langro: The installation concept needs to be considered. Will you communicate over Fieldbus? Will you use digital I/O? How spread out over the

CD1411PneumaticsLagro9737ac

Source: Festo

machine are the actuators? Ideally the valve bank will be fairly close to the actuators. This can be accomplished with a decentralized approach. Some valve systems allow adding branches from the main manifold for placing additional valves in remote parts of the machine, much closer to the cylinders at the point of actuation. A valve manifold system can also allow you to bring your I/O back to the valve manifold and enable you to utilize it as your main control device for the machine or cell.

Nobles: The main consideration is the type of communication the customer has in its installed base of equipment. If there are no other bus communications present, then the choice is made based on our supplier's preferred communication protocol.

Savela: For precise operation, closed-loop motion controllers need to work through zero-deadband servo-quality proportional valves that respond quickly to control inputs. And the valve should be placed as close as possible to the pneumatic cylinder.

CD1411PneumaticsHeadshotForishMarchelle2014Forish: When choosing the right pneumatic devices for digital control, the key factors are ease of connectivity, flexibility, and expandability. There are many options to connect pneumatic devices to the most common protocols on the market.

Pneumatics can be used to power certain simple linear motion requirements, but are there air supply and maintenance hassles that come with pneumatics?


Savela: Not if system-level design issues are considered when the design is done. For example, to avoid problems of not having enough supply pressure at times when motion is rapid, an appropriately sized accumulator should be used. And to avoid maintenance problems and control energy costs, the pump should be sized to meet the average system load. Most industrial/factory environments have pneumatic lines plumbed to most locations in the plant. There is typically minimal effort required to supply the air to the actuator.

Nobles: The hassles that go along with pneumatic systems are no more egregious than any other technology. Proper maintenance and education help the life of pneumatics and other systems.

Langro: All installations, be they pneumatic, hydraulic or electric, have their specific maintenance requirements. The maintenance of a pneumatic system is really fairly simple and involves ensuring that the air quality and operating pressure are properly maintained. There are visual indicators on the filter units that show when the filter element needs to be changed. Many suppliers can offer automatic drain systems as well, to avoid an overflow of water accumulating in the filter bowl. Differential pressure sensors can be integrated into the air prep system and can automatically send a signal to your PLC indicating a need for maintenance. This type of new advancement can simplify the maintenance aspects of a pneumatic system.

CD1411PneumaticsMaurerScott

Scott Maurer

Maurer: Like other plant utilities, compressed air requires conditioning and maintenance to avoid problems with the valves, cylinders and other tools that use it. Cooling water systems require various chemical treatments, as well as filtration to avoid fouling issues. Electrical systems benefit from power and signal conditioning to assure clean, consistent power and noise-free communication. Condensed water, compressor oils and particulates are the major culprits in a compressed air system, but they can be addressed easily with supply side and supplemental point-of-use methods. A properly selected drying and filtration system, along with a solid PM program, can minimize operational issues.

McDermott: The single biggest hassle in a pneumatic system is eliminating leaks. Leaks cost an incredible amount of money, but in every facility I visit you can hear the hiss of at least one leak. To be honest, I don't understand why this is so; eliminating leaks is easy and the simplest way to decrease operating costs.

Does the availability of high-pressure compressed air have an impact on whether to use a pneumatic solution because the lack of pressurized air or gas would necessitate installing compressors, tubing and valves?

Maurer: Certainly, the existence of a compressed air system impacts whether a user elects a pneumatic solution. For a plant without a compressed air system, there is the obvious cost/benefit analysis of adding another utility. Are there other processes that will be added that can utilize any excess system capacity to be installed, or is a right-sized solution for a single process more appropriate? Any installation of pneumatically operated equipment should include an evaluation of the system's supply capabilities. If you are adding demand to an existing system, will the additional consumption exceed its capabilities? Unlike tripping a breaker on an overloaded electrical circuit, an overloaded pneumatic system starves part or all of the system when confronted with excessive demand. So whether you are evaluating adding that first piece of pneumatic equipment to a plant or the hundredth, you need to consider the costs associated with the required compressor capacity.

McDermott: When a plant already has compressed air available, then pneumatic solutions should be considered. If the facility doesn't already have compressed air, the application must be so biased toward pneumatics as to be obvious to anyone that it must be that way.

Langro: Most industrial facilities are using compressed air for tools, such as screwdrivers, wrenches and other devices. This definitely makes the decision to use pneumatics feasible because the facility already has an infrastructure in place for a pneumatic system.

Nobles: If compressed air isn't present, it does affect the overall economic picture for an installation. When a compressor is needed, an electromechanical system can be more attractive.

How do operating conditions such as contaminated, explosive, wet or corrosive environments affect the choice between pneumatic and electromechanical solutions?

Nobles: The proper choice of components based on environmental conditions is essential for the long life of both pneumatic and electromechanical systems. Certain applications in explosive environments can be implemented with significantly less cost using a pneumatic system.

Marks: Our paint application process almost entirely uses pneumatic applicators. This approach provides quality control and hazard-avoidance benefits in terms of safety implications. The applicators are located inside of a paint booth, an explosive environment in which an electrical spark could cause ignition. Every effort must therefore be made to keep electrical components outside of the booth.
Langro: Operating conditions can have a great impact on what type of system is selected. Hazardous environments can be more suited to pneumatic or electro-pneumatic solutions than to an electromechanical technology. A purely pneumatic solution can eliminate the possibility of sparking from an electrical connector or heat buildup from operating a motor or other electrical device. Even solenoid-operated valves have the capability to be made explosion-proof or intrinsically safe, enabling them to be operated in a Class I, Div. 1 area. Pneumatics are also more easily protected in washdown areas because it's necessary to take more precautions with electromechanical solutions.

CD1411PneumaticsTJprojectMcDermottHeadshotMcDermott: Operating conditions absolutely have a role in selecting the motive means. Hazardous atmospheres benefit from a pneumatic solution. Other types of environments such as corrosive or wet are equally harsh on electric and pneumatic solutions.

Savela: Obviously, pneumatic applications using air or inert gas don't provide an ignition risk at the actuator, and pneumatics can be used in harsher and/or more humid environments. The latter is one reason why pneumatics is a standard means of powering food handling and packaging or bottling machines. Corrosive and wet environments may require the use of stainless steel cylinders and rods to tolerate a challenging environment, but this is less expensive than equally robust electro-mechanical solutions.

Are your machine pneumatics electronically controlled?

McDermott: Electronic control of pneumatic systems is the only way we build these days. The benefits of easy function change via PLC programming far outweigh the cost of the logic hardware.

Langro: Typically most machines using pneumatics are electronically controlled. Electrically controlled machines utilizing PLCs and networks give plant managers, operators and maintenance staff much more information about the status of production and the machine. This helps minimize downtime and scrapped parts, and can improve the overall profitability and productivity of a facility.

Savela: With electro-pneumatic motion controls that have special support for controlling fluid power systems, machines can operate just as precisely as systems using electric motors, while providing the advantages that fluid power brings.


What sorts of safety concerns do pneumatics create or alleviate?

McDermott: Pneumatics can enhance safety when the application is in a hazardous environment where electrical actuators or motors are prohibited. The electrically activated valves are placed in a nonhazardous area, and the pneumatic lines lead to the actuators in the hazardous environment.

Marks: One of the safety concerns associated with pneumatics is control of stored energy. This comes into play during associate parts loading at point of operation as well as in lockout/tagout maintenance repair operations. The stored energy has the potential to release at unintended times and make contact with personnel, introducing the potential for personal injury. However, pneumatics does eliminate the explosion potential that would be present using electrical applications in our paint operations.

Nobles: Pneumatics is no more or no less a safety concern than other technologies. Proper maintenance and education help prevent problems with pneumatic systems.